PAN • TILT • ZOOM COLOR CAMERA
-
PTC 200C
INSTRUCTION MANUAL
Please read this instruction manual carefully before using this PTC-200C
and keep it for future reference.
CAUTION
RISK OF ELECTRIC
INFORMATION
This equipment has been tested
and found to comply with the
limits for Class A digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference
when the equipment is operated
in a commercial environment.
This equipment generates, use,
and can radiate radio frequency
energy and, if not installed and
used in accordance with the
instruction manual, may cause
harmful interference to radio
communications. Operation of
this equipment in a residential
area is likely to cause harmful
interference in which case the
user will be required to correct
the interference at his own
SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral
triangle, is intended to alert the
user to the presence of
uninsulated "dangerous voltage"
within the product's enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
• Do not use any power supply other
than specified.
expense.
USER-INSTALLER
WARNING
CAUTION: Your authority to
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
operate this FCC verified
equipment could be voided if you
make changes or modifications
not expressly approved by the
party responsible for compliance
to Part of the FCC Rules.
* The CAUTION label is attached on
the base of product.
- 2 -
HANDLING PRECAUTIONS
Be sure to use the provided AC adapter.
Do not leave the Camera under direct sunlight or by heater, or the
Camera may be discolored, or damaged.
Do not place the Camera in any humid, dusty, windy or vibrating
location. Use the Camera in the following environmental condition:
Temperature: 0 °C ~ 40 °C (32 ° ~ 104 °F)
Humidity:
30% ~ 85% (No condensation)
Use a soft, dry cloth for cleaning. Do not use any volatile solvent, such
as thinner or benzine.
Do not directly point the camera lens into the sun, or the camera may be
damaged.
Caring for the batteries:
• If the Camera is not used for long time, remove the batteries from the
remote controller.
• Do not use rechargeable Ni-Cd batteries.
• Do not use new and old batteries, or batteries of different type
together.
• Do not try to recharge or short-circuit the batteries.
Do not operate the PAN/TILT motion continuously for a long time, or the
life of the Camera will be shortened.
- 3 -
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .........................................1
HANDLING PRECAUTIONS............................................................3
1. PART NAMES AND FUNCTIONS....................................................5
.............................................
2. WIRELESS REMOTE CONTROLLER
7
9
....................................................................................
3. SETTING UP
........................................................
.....................................................
.....................................
4. OPERATION PROCEDURES
[1] Power supply to the Camera
14
14
14
15
16
17
17
18
19
22
22
22
23
24
[2] Turning ON/OFF of the Camera power
..................................................................
[3] Operating PAN/TILT
...........................................................................
[4] Lens operation
...........................................................
[5] BLC (Back Light Control)
........................................................................
[6] Preset operation
...........................................................
5. THE ID NUMBER SETTING
..............................................................
6. OSD (On-Screen Display)
........................................................
7. ALARM IN/OUT TERMINALS
................................................................................
..............................................................................
.....................................................................
[1] Alarm input
[2] Alarm output
8. ALL CLEAR SWITCH
...........................................................................................
9. RS-485
....
10. TERMINATING RESISTANCE AND ID ADDRESS SETTINGS 25
.............................................
[1] Setting the terminating resistance
25
25
28
...............................................................
[2] Setting the ID address
........................................................
11. TROUBLESHOOTING HINTS
12. SPECIFICATIONS..........................................................................29
13 SUPPLIED ACCESSORIES...........................................................30
- 4 -
1. PART NAMES AND FUNCTIONS
Overall View
LED
INFRARED SENSOR
BASE
LENS
CAM ERA HEAD
ALARM IN TERM INAL
RS-485 IN TERM INAL
DIP Switch (4)
TERM INAL BLOCK
DIP Switch (10)
RS-485 OUT TERM INAL
ALARM OUT TERM INAL
DC IN
INFRARED SENSOR
COM POSITE-VIDEO OUT
(RCA pin jack)
This camera is designed to mount on ceiling panels only.
- 5 -
Wireless Remote Controller
15
RESET
ID
1
POWER
14
16
BACK LIGHT
17
PRESET
2
OPEN
5
6
7
NEAR
18
3
4
NUMBER (1 6)
CLOSE
AUTO
FAR
AUTO
11
10
HOME
Directions
8
9
TELE
WIDE
12
13
CURSOR/PAN-TILT
MENU
No.
Button Name
POWER
OPEN
Function
Reference Page
1
2
3
4
5
6
To turn ON/OFF the Camera power.
To open the iris manually.
P.19
P.16
P.16
CLOSE
AUTO
To close the iris manually.
To iris automatically.
P.16
NEAR
To move the focus near.
P.16
FAR
To move the focus far.
P.16
7
8
AUTO
To focus automatically.
P.16
TELE
To zoom in.
P.16
9
WIDE
To zoom out.
P.16
10
Direction
To change the Camera head direction.
To operate the OSD*1 cursor.
To turn the Camera head to the front.
To operate the OSD*1 cursor.
To turn ON/OFF the OSD*1 display.
To switch the operation mode between the menu
operation and the PAN-TILT operation.
P.15
(
)
P.19, P.20, P.21
P.15
HOME
11
P.19, P.20, P.21
P.18, P.19, P.20, P.21
P.19
12 MENU
CURSOR/
PAN-TILT
BACK LIGHT Back light control.
13
14
15
16
P.17, P.20
P.15
RESET
To readjust the Camera head and LENS position.
PRESET
To register the preset.
P.17
17 ID
To operate multiple Cameras individually.
To set the preset position and the ID No.
P.14, P.18
P.17, P.18
NUMBER
(1~6)
*1 OSD (On-Screen Display)
18
- 6 -
2. WIRELESS REMOTE CONTROLLER
Point the infrared emitting window of the wireless remote controller at the infrared sensor
of the Camera, located at the front, and the rear panel, and select the desired function.
Receivable range
Note: The infrared sensors may receive the infrared rays only within a narrower
receivable range or may not receive them at all depending on the ambient
environment, such as being placed under the sunlight or near an inverter
fluorescent lamp. In such case, relocate the installation place of the
receiving side or block off the sunlight.
- 7 -
Preparation
Remove the battery case cover by pressing downward on the [ ] mark part in the
direction as indicated by the arrow.
Install 2 pcs. of batteries (type R03,AAA) into the case in the direction as indicated
there.
Note: Install the batteries with the proper
to
and
to
polarity.
Note: For dry cells, be sure to use the size AAA.
Note: Change the batteries at least once a year or when even nesessary.
Note: The batteries supplied with the Camera are only for use in initially
confirming the operation of the Camera.
It is not guaranteed that these batteries will work effectively for the
indicated period.
When multiple Cameras are operated through the wireless remote
controller
Refer to "5. THE ID NUMBER SETTING" on P. 18.
- 8 -
3. SETTING UP
[1] Installation
Note: When carrying the Camera, be sure to hold the base.
Note: Do not turn the Camera head in the PAN-TILT direction by hand, or
the Camera head may be broken.
(1) Mounting the Fixing Plate
• Put 4 Hexagon Head Bolts M5x40 (supplied)
SCREW M 3x5 (attached), 4 PCS
through the Fixing Plate, and screw the Fixing
Plate to the Main Unit with 4 Screws M3x5
(supplied).
FIXING PLATE
HEXAGON HEAD BOLT M 5x40, 4 PCS
Note: For fastening the Fixing Plate, be
sure to use the 4 Phillips-head
Screw M3x5 (supplied). Be careful
that using any screws other than
the supplied may damage the
inside of the Main Unit. (Do not use
longer screws)
M AIN UNIT
- 9 -
(2) Making mounting holes to the Ceiling Tile
Make 4 holes of 8mm (5/16 in.) to the
•
Ceiling Tile as shown.
M OUNTING HOLE
8m m (5/16 in.), 4 LOCATIONS
102m m (4 in.)
70m m (2-3/4 in.)
BACK
54m m
(2-1/8 in.)
FRONT
CEILING TILE
(t1/2 in. 1 in.)
t= thickness
- 10 -
(3) Fixing the Main Unit
• Put the Ceiling Tile between the Main Unit
and the Ceiling Plate, and fix the Main Unit by
fastening 4 Wing Nuts.
W ING NUT M 5 (supplied), 4 PCS
CEILING PLATE
M OUNTING HOLE: 5/16 in., 4 LOCATIONS
CEILING TILE
(t1/2inch-1inch)
t= thickness
HEXAGON HEAD BOLT M 5x40 (supplied), 4 PCS
M AIN UNIT
- 11 -
(4) Mounting the Safety Wires
• Loop up one end of the Safety Wires through
the respective safety wire looping holes made
on the Ceiling Plate, and then loop up the other
end of the same around the beams or anything
that is used to mount ceiling tile channel for
structure safety.
SAFETY W IRE (notsupplied)
SAFETY W IRE LOOPING HOLE
CEILING PLATE
CEILING TILE
- 12 -
Connection examples for the Camera
- 13 -
4. OPERATION PROCEDURES
[1] Power supply to the Camera
The Camera has no POWER switch. Power is supplied to the Camera when the AC
adapter is connected to the wall socket and the Camera.
When power is supplied to the Camera, the Camera turns to the right and then to the
center automatically (viewed from the front), returning the Camera position to the
detault home position.
[2] Turning ON/OFF of the Camera power
(1) Turning OFF the Camera
1
• When the Camera is ready for operation
17
1
through the wireless remote control and
POWER button is pressed, the Camera
power is turned OFF. (However, even after
the Camera is turned OFF, power is still
being supplied to the Camera as power
supply to the Camera is not OFF.)
• The image disappears, and the LED on the
Camera lights up in red. Now, no buttons on
the wireless remote control are functional
1
other than
POWER button and
ID button.
17
• When the TIMER OFF function is ON (refer to the settings in the OSD Menu screen),
Camera power is turned OFF automatically upon the lapse of the set time.
Note: When the Camera is not in use, make it a rule to keep the Camera
OFF. This will save power consumption. When the Camera is not to
be used for a long time, it is advisable to unplug the AC adapter to
render the Camera OFF.
(2) Turning ON the Camera
1
• When the Camera is OFF and
turned ON.
POWER button is pressed, the Camera power is
• The image appears, and the LED on the Camera goes out. Now, the Camera is ready
for operation of all functions through the wireless remote control.
• If the ID number is changed (Refer to "5. THE ID NUMBER SETTING" on P.18), the
Camera power may not be turned ON. In such case, redo the ID number setting, and
1
press
POWER button.
- 14 -
[3] Operating PAN/TILT
10
• While watching the screen, press any of
15
(UP, DOWN, LEFT, RIGHT)
direction buttons for the direction in which
you want to watch the image.
• To change the direction minutely, jog the
direction button. To change the direction
largely, hold down the direction button.
• Two operation modes are available
according to the speed: AUTO mode
changing the speed according to the zoom
position, and MANUAL mode setting the
11
10
speed manually. (Refer to the settings in the OSD Menu screen.)
11
• When
HOME button is pressed, the Camera turns to the front (and the lens
moves to the WIDE side).
15
• If the Camera direction is changed manually by mistake, press
RESET
button. Then, the Camera remembers the last PAN/TILT position in memory.
- 15 -
[4] Lens operation
(1) Zoom operation
• The object is zoomed in (appears larger in the
8
screen) when
TELE button of ZOOM is
2
pressed, or zoomed out (appears smaller in the
5
3
6
9
screen) when
pressed.
WIDE button of ZOOM is
4
7
9
8
• When
TELE button or
WIDE button is
8
9
held down for over one second, the zoom speed
increases.
(2) Focus operation
7
• When
AUTO button of FOCUS is pressed,
FULL AUTO FOCUS status is established. (However, focusing may be difficult
for such objects as listed below.)
Objects with no contrast between light and
dark, such as white walls and night views
Objects reflecting an intensive light
Objects moving fast
Objects with many horizontal stripes, such as
blinds
Objects viewed through a glass pane with
water drops or stains
6
5
• To adjust the focus manually, press
NEAR button or
FAR button.
5
When
When
NEAR button is pressed, the focus shifts near to you.
FAR button is pressed, the focus shifts far away from you.
6
(3) Iris operation
4
• When
AUTO button of the IRIS, the AUTO IRIS status (the brightness
remains unchanged even if the object is changed) is established.
2
3
• To adjust the iris manually, press
OPEN button or
CLOSE button.
2
When
When
OPEN button is pressed, the iris opens.
CLOSE button is pressed, the iris closes.
3
- 16 -
[5] BLC (Back Light Control)
In case the back lighting is too bright to shoot the
14
main object clearly, press
button.
BACK LIGHT
14
To cancel this mode, press the button.
[6] Preset operation
The Camera head direction, the zoom position, the
focus status and the brightness level can be
registered for as many as six settings.
The registration contents will be retained even if
the Camera power is turned OFF.
(1) Setting presets
16
18
• Set the Camera head direction, the zoom
position, the focus status and the brightness
level.
16
• When
PRESET button is pressed, the
LED on the Camera blinks in green (for 0.4
PRESET button again.
16
sec). To cancel this, press
18
• Then, press
one of the 1 through 6 buttons. Now, the registration is over, and
the LED on the Camera goes out. (The preset contents, if already registered, are
erased and overwritten.)
(2) Execution of preset
18
• When
one of the 1 through 6 buttons are pressed, the Camera head direction,
the zoom position, the focus status and the brightness level are set to that specific
preset position.
- 17 -
5. THE ID NUMBER SETTING
When multiple Cameras are laid out adjacently and operated via the wireless remote
controller, the Cameras receiving the infrared rays operate in unison in the same way. When
each Camera is allocated with a different ID No., the Camera can be controlled independently
when its ID No. is specified via the wireless remote controller. The ID Nos. can be allocated
for up to 6 Cameras.
(1) Setting an ID No.
• Turn ON only the camera to be set with an ID
17
No. Leave other adjacent Cameras in the OFF
position. (Unplug their AC adapters from the
18
Cameras or wall socket).
• Set the remote ID No. to the Camera. (See "6.
12
OSD (On-Screen Display)" on P. 19.) After
12
setting, close the Menu screen by pressing
MENU button. Then, repeat the ID No. setting
for all other Cameras in the same way.
(2) Operating the Cameras selectively
17
• Press
ID button, and the LED's of all adjacent Cameras will start blinking (at
17
18
intervals of 0.2 sec). (To cancel this, press
ID button again.) Then, press
1
through 6 buttons, and the LED's will go out, and selective operation by specifying
the ID No. will be ready. Now, only the selected Camera can be operated via the
wireless remote controller.
(3) Canceling the specific ID of the Cameras
17
• Hold down
ID button for over 2 sec, and the blinking LED on the Camera will
17
light up. Then, unhand
ID button. Now, the selective operation has been
cancelled, and all adjacent Cameras start operation via the wireless remote controller.
• Alternatively, the selective operation by specifying the ID No. can also be cancelled
by unplugging the DC jack from the Camera and turning ON the Camera power again.
- 18 -
6. OSD (On-Screen Display)
12
The
MENU button is used to turn ON/OFF
1
the OSD display. When the Sub menu is
displayed, the screen goes back to the previous
screen.
14
10
When the OSD display is available,
11
direction buttons and
HOME button
11
10
12
function as the menu operation keys.
To halt the menu operation and perform the PAN-
13
13
TILT operation, press
CURSOR/PAN-TILT
13
button. To resume the menu operation, press
CURSOR/PAN-TILT button again.
OSD Display menu
<<MAIN MENU>>
(1) MAIN CONTROL
(2) CAMERA SETUP
(3) TITLE SET
12
SELECT
SELECT
ENTER
(Return to
MENU )
(4) PAN TILT MOTOR
12
MENU )
(1) MAIN CONTROL
<1> TITLE
ADJUST
(Return to
ON/OFF: To change the ON/OFF of the character in the
bottom of the screen.
<2> SELECT
PRESET/CAMERA: To change the title to be displayed.
(This setting is enabled only when the above TITLE is ON.)
PRESET: To display preset position names from 1 to 6.
CAMERA: To display the name of the Camera.
ON/OFF: To display the preset position in the screen upon
its registration (for about 2 sec).
<3> SET INDICATE
<4> REMOTE ID
1~6: To set the ID No. of the Camera for the selective
operation via the wireless remote control.
If the ID No. is not to be set, set this to "0."
(This has been factory set to "0.")
<5> OFF TIMER
OFF, 5min, 10min, 30min 1h, 2h, 5h: To set the time for the
Low Power Consumption mode.
If no operation status continues longer than the above set
time, the Camera power will be turned OFF automatically.
1
To turn ON the Camera power again, press
button. (This has been factory set to "OFF.")
POWER
- 19 -
<6> ALARM IN
Sets the alarm position time [10 sec (default), 20 sec, 30
sec, 1 min, 5 min, 10 min, OFF]. When the set time has
passed, automatic resetting is made to the lastly executed
preset position.
<7> ALARM OUT
Sets the alarm signal output time [0.1 sec (default), 0.5 sec,
1 sec, 2 sec, 5 sec, 10 sec, 30 sec].
12
MENU )
(2) CAMERA SETUP
<1> BLC
SELECT
ADJUST
(Return to
ON/OFF: To balance the difference between light and dark
background.
This function can also be operated easily by pressing
14
BACK LIGHT button on the wireless remote control.
<2> AGC
0dB, 4dB, 8dB, 12dB, 16dB, 20dB, 24dB: To adjust the
maximum AGC gain.
<3> AP GAIN
<4> FL
-6 to +9: To adjust the contour correction level between.
ON/OFF: To change the ON/OFF of the flicker correction.
To go to the next screen.
<5> NEXT PAGE
<6> MEMORY
To save the current settings of the Camera by pressing
11
HOME button.
<7> CLEAR
To reset the settings of the Camera to the factory-settings
11
by pressing
HOME button.
<8> WB
To
To adjust the white balance by way of the automatic
following. (The white balance will not be effected by colors
of lighting changes.)
1. ATW
2. AWC
change
the White
Balance
mode.
To adjust the white balance by way of one-push of button.
The white balance is adjusted once by selecting the AWC
11
mode and pressing
HOME button. When the WB mode
has been changed or the R-SHIFT or B-SHIFT function has
been changed, the white balance must be adjusted again by
11
pressing
HOME button.
To be used indoors. The color temperature is 3,200K.
To be used outdoors. The color temperature is 6,300K.
To be used under fluorescent lamps. The color temperature
is 4,200K.
3. INDOOR
4. OUTDOOR
5. LIGHT
<9> R SHIFT *1
<10> B SHIFT *2
±30: The larger this value is, the screen is more reddish.
±30: The larger this value is, the screen is more bluish.
To adjust the intensity of red.
<11>
1. R GAIN
2. B GAIN
COLOR
To adjust the intensity of blue.
To adjust 3. RY HUE
the color. 4. BY HUE
<12> PREVIOUS PAGE
To adjust the hue of red.
To adjust the hue to blue.
To return to the previous screen.
- 20 -
*1: <9> "R SHIFT" and <10> "B SHIFT" are available in 2 types, respectively: one for the
ATW and AWC functions, and the other for the INDOOR, OUTDOOR and LIGHT
functions. For example, it is possible to set "R SHIFT" to +10 in the ATW mode and
to ± 0 in the INDOOR mode.
*2: <11> "COLOR" is available for all modes irrespective of the mode of "WB".
11
*3: To change and save the Camera settings, be sure to press
>MEMORY display on P. 1.
HOME button in the
(3) TITLE SET
SELECT
• To set the title for each preset position and Camera.
10
Make the title to be set blink, and press
direction
ADJUST
button to go to the set character. Then, set the character
12
10
(Return to
MENU )
one by one by using
direction buttons.
The types of characters that can be set are alphabetic
characters in capital and small ("A" through "Z" and "a"
through "z") and symbols (e.g., < > - / . :). After setting all,
11
press
HOME button to save the settings.
12
MENU )
(4) PAN TILT MOTOR
<1> MOTOR SPEED
SELECT
ADJUST
(Return to
• To set the motor speed when the PAN-TILT function is in
operation.
• AUTO: The operation speed can be changed automatically
according to the zoom position.
• MANUAL: The operation speed can be selected freely.
• To set the motor speed when "MANUAL" has been
selected for the motor speed. The motor speed can be
changed in 8 steps from 0 to 7.
<2> SPEED
<3> L/R DIRECTION
• STANDARD/REVERSE: To change the PAN direction.
- 21 -
7. ALARM IN/OUT TERMINALS
[1] Alarm input
By short-circuiting the ALARM 1 IN or ALARM 2 IN Terminal Block to the GND
terminal on the Terminal Block, the Camera moves to the allocated preset position.
• When short-circuiting the ALARM 1 IN terminal to the GND terminal,
the Camera moves to the preset position 1.
• When short-circuiting the ALARM 2 IN terminal to the GND terminal,
the Camera moves to the preset position 2.
Then, when the time set from the OSD menu has passed, the Camera moves back
automatically to the lastly executed preset position.
• Regarding time setting, refer to the setting in the OSD menu screen.
[2] Alarm output
When the alarm input signal has been activated and the Camera has moved to the specified
position, the alarm signal is outputted at the ALARM OUT terminal for the time preset
from the OSD menu.
• Regarding time setting, refer to the setting in the OSD menu screen.
Pin arrangement
Terminal name
1 IN
Function
O
Inputs the alarm signal <1>.
Grounds.
2
GND
1
GND
-
GND
OUT
OUT
2 IN
Inputs the alarm signal <2>.
Outputs the alarm signal.
OUT
- 22 -
8. ALL CLEAR SWITCH
The PAN-TILT settings, the LENS settings, the preset settings, the ID settings and the
Camera settings by means of the OSD can be reset to the factory-settings by turning ON the
switch No. 2 of the DIP Switch (4) on the bottom of the Camera before turning ON the
power supply to the Camera and then turning OFF the same switch after turning ON the
power supply to the Camera.
Note: For all other switches (No. 1, No. 3 and No. 4) of the 4-DIP Switch,
be sure to turn them OFF, or operation via the wireless remote
controller or by other means will not work.
Switch assignment
Switch No.
Normal
OFF
Operation
None
Function
N/A
1
2
3
4
OFF
ON OFF
None
ALL CLEAR
N/A
OFF
OFF
None
N/A
DIP Switch (4)
1
2
3
4
OFF
DIP Switch (4)
ALL CLEAR SW ITCH
BASE OF M AIN UNIT
- 23 -
9. RS-485
This system can be controlled from the PC by connecting the RS-485 terminal on the 9-pin
Terminal Block to the PC via an RS-485 converter.
Make the connection as shown below.
Each camera can be set for the ID address via a 10-pin DIP Switch located on the bottom so
that a selected camera can be controlled.
Up to 223 Cameras can be controlled from one PC.
To raise the reliability, connect the DATA (+)and the DATA (-) with a twist pair cable.
To protect this system and the PC, be sure to turn OFF the POWER switches of all units
before starting the connection.
［RS-485］
IN＋
IN－
［RS-485］
D＋
D－
［RS-485］
IN＋
IN－
OUT＋
OUT－
OUT＋
OUT－
Communication specifications
• Communication mode: Synchronous half duplex
• Communication speed: 9600bps
• Start bit:
• Stop bit:
• Parity bit:
1 bit
1 bit
None
Pin assignment
Terminal name Signal name
Function
+IN
-IN
DATA (+)
DATA (-)
DATA (+)
DATA (-)
GND
+ side: Inputs the transmitted/received
- side: Inputs the transmitted/received
+ side: Outputs the transmitted/received data.
- side: Outputs the transmitted/received data.
Grounds.
+OUT
-OUT
GND
ND
1
GND
+
+
-
-
OUT
If you need the data format specifications and the command table, please contact our
distributor.
- 24 -
10. TERMINATING RESISTANCE AND ID ADDRESS SETTINGS
The ID address of the RS-485 and the terminating resistance can be set by using the
switches Nos. 1 through 9 of the DIP Switch (10) located on the bottom of the Main Unit.
Switch No.
Function
Sets the ID address.
1 – 8
9
Turns ON/OFF the terminating resistance
None
10
[1] Setting the terminating resistance
The terminating resistance is built in each Camera, and it can be turned ON/OFF by using
the pin No. 9 of the DIP Switch (10) of each Camera. To prevent the attenuation of the
signal, turn ON the terminating resistances of the 2 Cameras located at both ends of the
longest route, of all cameras to be connected to the RS-485 interface, and turn OFF the
terminating resistances of the other Cameras.
DIP Switch (10)
1
2
3
4
5
6
7
8
9
10
DIP Switch (10)
OFF
SETTINGS OF ID ADDRESS
TERM INATING RESISTANCE
BASE OF M AIN UNIT
[2] Setting the ID address
The ID address for communication of the RS-485 can be set by using the switches No. 1
through 8 of the DIP Switch (10). (Refer to "Setting the ID address" table - P26, 27)
- 25 -
Setting the ID address
Cam era
Switch No. ofDIP Switch (10)
Cam era
ID address
56
Switch No. ofDIP Switch (10)
ID address
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Disabled OFF OFF OFF OFF OFF OFF OFF OFF
OFF OFF OFF ON ON ON OFF OFF
ON OFF OFF ON ON ON OFF OFF
OFF ON OFF ON ON ON OFF OFF
ON ON OFF ON ON ON OFF OFF
OFF OFF ON ON ON ON OFF OFF
ON OFF ON ON ON ON OFF OFF
OFF ON ON ON ON ON OFF OFF
ON ON ON ON ON ON OFF OFF
OFF OFF OFF OFF OFF OFF ON OFF
ON OFF OFF OFF OFF OFF ON OFF
OFF ON OFF OFF OFF OFF ON OFF
ON ON OFF OFF OFF OFF ON OFF
OFF OFF ON OFF OFF OFF ON OFF
ON OFF ON OFF OFF OFF ON OFF
OFF ON ON OFF OFF OFF ON OFF
ON ON ON OFF OFF OFF ON OFF
OFF OFF OFF ON OFF OFF ON OFF
ON OFF OFF ON OFF OFF ON OFF
OFF ON OFF ON OFF OFF ON OFF
ON ON OFF ON OFF OFF ON OFF
OFF OFF ON ON OFF OFF ON OFF
ON OFF ON ON OFF OFF ON OFF
OFF ON ON ON OFF OFF ON OFF
ON ON ON ON OFF OFF ON OFF
OFF OFF OFF OFF ON OFF ON OFF
ON OFF OFF OFF ON OFF ON OFF
OFF ON OFF OFF ON OFF ON OFF
ON ON OFF OFF ON OFF ON OFF
OFF OFF ON OFF ON OFF ON OFF
ON OFF ON OFF ON OFF ON OFF
OFF ON ON OFF ON OFF ON OFF
ON ON ON OFF ON OFF ON OFF
OFF OFF OFF ON ON OFF ON OFF
ON OFF OFF ON ON OFF ON OFF
OFF ON OFF ON ON OFF ON OFF
ON ON OFF ON ON OFF ON OFF
OFF OFF ON ON ON OFF ON OFF
ON OFF ON ON ON OFF ON OFF
OFF ON ON ON ON OFF ON OFF
ON ON ON ON ON OFF ON OFF
OFF OFF OFF OFF OFF ON ON OFF
ON OFF OFF OFF OFF ON ON OFF
OFF ON OFF OFF OFF ON ON OFF
ON ON OFF OFF OFF ON ON OFF
OFF OFF ON OFF OFF ON ON OFF
ON OFF ON OFF OFF ON ON OFF
OFF ON ON OFF OFF ON ON OFF
ON ON ON OFF OFF ON ON OFF
OFF OFF OFF ON OFF ON ON OFF
ON OFF OFF ON OFF ON ON OFF
OFF ON OFF ON OFF ON ON OFF
ON ON OFF ON OFF ON ON OFF
OFF OFF ON ON OFF ON ON OFF
ON OFF ON ON OFF ON ON OFF
OFF ON ON ON OFF ON ON OFF
ON ON ON ON OFF ON ON OFF
1
ON OFF OFF OFF OFF OFF OFF OFF
OFF ON OFF OFF OFF OFF OFF OFF
ON ON OFF OFF OFF OFF OFF OFF
OFF OFF ON OFF OFF OFF OFF OFF
ON OFF ON OFF OFF OFF OFF OFF
OFF ON ON OFF OFF OFF OFF OFF
ON ON ON OFF OFF OFF OFF OFF
OFF OFF OFF ON OFF OFF OFF OFF
ON OFF OFF ON OFF OFF OFF OFF
OFF ON OFF ON OFF OFF OFF OFF
ON ON OFF ON OFF OFF OFF OFF
OFF OFF ON ON OFF OFF OFF OFF
ON OFF ON ON OFF OFF OFF OFF
OFF ON ON ON OFF OFF OFF OFF
ON ON ON ON OFF OFF OFF OFF
OFF OFF OFF OFF ON OFF OFF OFF
ON OFF OFF OFF ON OFF OFF OFF
OFF ON OFF OFF ON OFF OFF OFF
ON ON OFF OFF ON OFF OFF OFF
OFF OFF ON OFF ON OFF OFF OFF
ON OFF ON OFF ON OFF OFF OFF
OFF ON ON OFF ON OFF OFF OFF
ON ON ON OFF ON OFF OFF OFF
OFF OFF OFF ON ON OFF OFF OFF
ON OFF OFF ON ON OFF OFF OFF
OFF ON OFF ON ON OFF OFF OFF
ON ON OFF ON ON OFF OFF OFF
OFF OFF ON ON ON OFF OFF OFF
ON OFF ON ON ON OFF OFF OFF
OFF ON ON ON ON OFF OFF OFF
ON ON ON ON ON OFF OFF OFF
OFF OFF OFF OFF OFF ON OFF OFF
ON OFF OFF OFF OFF ON OFF OFF
OFF ON OFF OFF OFF ON OFF OFF
ON ON OFF OFF OFF ON OFF OFF
OFF OFF ON OFF OFF ON OFF OFF
ON OFF ON OFF OFF ON OFF OFF
OFF ON ON OFF OFF ON OFF OFF
ON ON ON OFF OFF ON OFF OFF
OFF OFF OFF ON OFF ON OFF OFF
ON OFF OFF ON OFF ON OFF OFF
OFF ON OFF ON OFF ON OFF OFF
ON ON OFF ON OFF ON OFF OFF
OFF OFF ON ON OFF ON OFF OFF
ON OFF ON ON OFF ON OFF OFF
OFF ON ON ON OFF ON OFF OFF
ON ON ON ON OFF ON OFF OFF
OFF OFF OFF OFF ON ON OFF OFF
ON OFF OFF OFF ON ON OFF OFF
OFF ON OFF OFF ON ON OFF OFF
ON ON OFF OFF ON ON OFF OFF
OFF OFF ON OFF ON ON OFF OFF
ON OFF ON OFF ON ON OFF OFF
OFF ON ON OFF ON ON OFF OFF
ON ON ON OFF ON ON OFF OFF
57
2
58
3
59
4
60
5
61
6
62
7
63
8
64
9
65
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
- 26 -
Cam era
ID address
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
Switch No. ofDIP Switch (10)
Cam era
ID address
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
Switch No. ofDIP Switch (10)
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OFF OFF OFF OFF ON ON ON OFF
ON OFF OFF OFF ON ON ON OFF
OFF ON OFF OFF ON ON ON OFF
ON ON OFF OFF ON ON ON OFF
OFF OFF ON OFF ON ON ON OFF
ON OFF ON OFF ON ON ON OFF
OFF ON ON OFF ON ON ON OFF
ON ON ON OFF ON ON ON OFF
OFF OFF OFF ON ON ON ON OFF
ON OFF OFF ON ON ON ON OFF
OFF ON OFF ON ON ON ON OFF
ON ON OFF ON ON ON ON OFF
OFF OFF ON ON ON ON ON OFF
ON OFF ON ON ON ON ON OFF
OFF ON ON ON ON ON ON OFF
ON ON ON ON ON ON ON OFF
OFF OFF OFF OFF OFF OFF OFF ON
ON OFF OFF OFF OFF OFF OFF ON
OFF ON OFF OFF OFF OFF OFF ON
ON ON OFF OFF OFF OFF OFF ON
OFF OFF ON OFF OFF OFF OFF ON
ON OFF ON OFF OFF OFF OFF ON
OFF ON ON OFF OFF OFF OFF ON
ON ON ON OFF OFF OFF OFF ON
OFF OFF OFF ON OFF OFF OFF ON
ON OFF OFF ON OFF OFF OFF ON
OFF ON OFF ON OFF OFF OFF ON
ON ON OFF ON OFF OFF OFF ON
OFF OFF ON ON OFF OFF OFF ON
ON OFF ON ON OFF OFF OFF ON
OFF ON ON ON OFF OFF OFF ON
ON ON ON ON OFF OFF OFF ON
OFF OFF OFF OFF ON OFF OFF ON
ON OFF OFF OFF ON OFF OFF ON
OFF ON OFF OFF ON OFF OFF ON
ON ON OFF OFF ON OFF OFF ON
OFF OFF ON OFF ON OFF OFF ON
ON OFF ON OFF ON OFF OFF ON
OFF ON ON OFF ON OFF OFF ON
ON ON ON OFF ON OFF OFF ON
OFF OFF OFF ON ON OFF OFF ON
ON OFF OFF ON ON OFF OFF ON
OFF ON OFF ON ON OFF OFF ON
ON ON OFF ON ON OFF OFF ON
OFF OFF ON ON ON OFF OFF ON
ON OFF ON ON ON OFF OFF ON
OFF ON ON ON ON OFF OFF ON
ON ON ON ON ON OFF OFF ON
OFF OFF OFF OFF OFF ON OFF ON
ON OFF OFF OFF OFF ON OFF ON
OFF ON OFF OFF OFF ON OFF ON
ON ON OFF OFF OFF ON OFF ON
OFF OFF ON OFF OFF ON OFF ON
ON OFF ON OFF OFF ON OFF ON
OFF ON ON OFF OFF ON OFF ON
ON ON ON OFF OFF ON OFF ON
OFF OFF OFF ON OFF ON OFF ON
ON OFF OFF ON OFF ON OFF ON
OFF ON OFF ON OFF ON OFF ON
ON ON OFF ON OFF ON OFF ON
OFF OFF ON ON OFF ON OFF ON
ON OFF ON ON OFF ON OFF ON
OFF ON ON ON OFF ON OFF ON
ON ON ON ON OFF ON OFF ON
OFF OFF OFF OFF ON ON OFF ON
ON OFF OFF OFF ON ON OFF ON
OFF ON OFF OFF ON ON OFF ON
ON ON OFF OFF ON ON OFF ON
OFF OFF ON OFF ON ON OFF ON
ON OFF ON OFF ON ON OFF ON
OFF ON ON OFF ON ON OFF ON
ON ON ON OFF ON ON OFF ON
OFF OFF OFF ON ON ON OFF ON
ON OFF OFF ON ON ON OFF ON
OFF ON OFF ON ON ON OFF ON
ON ON OFF ON ON ON OFF ON
OFF OFF ON ON ON ON OFF ON
ON OFF ON ON ON ON OFF ON
OFF ON ON ON ON ON OFF ON
ON ON ON ON ON ON OFF ON
OFF OFF OFF OFF OFF OFF ON ON
ON OFF OFF OFF OFF OFF ON ON
OFF ON OFF OFF OFF OFF ON ON
ON ON OFF OFF OFF OFF ON ON
OFF OFF ON OFF OFF OFF ON ON
ON OFF ON OFF OFF OFF ON ON
OFF ON ON OFF OFF OFF ON ON
ON ON ON OFF OFF OFF ON ON
OFF OFF OFF ON OFF OFF ON ON
ON OFF OFF ON OFF OFF ON ON
OFF ON OFF ON OFF OFF ON ON
ON ON OFF ON OFF OFF ON ON
OFF OFF ON ON OFF OFF ON ON
ON OFF ON ON OFF OFF ON ON
OFF ON ON ON OFF OFF ON ON
ON ON ON ON OFF OFF ON ON
OFF OFF OFF OFF ON OFF ON ON
ON OFF OFF OFF ON OFF ON ON
OFF ON OFF OFF ON OFF ON ON
ON ON OFF OFF ON OFF ON ON
OFF OFF ON OFF ON OFF ON ON
ON OFF ON OFF ON OFF ON ON
OFF ON ON OFF ON OFF ON ON
ON ON ON OFF ON OFF ON ON
OFF OFF OFF ON ON OFF ON ON
ON OFF OFF ON ON OFF ON ON
OFF ON OFF ON ON OFF ON ON
ON ON OFF ON ON OFF ON ON
OFF OFF ON ON ON OFF ON ON
ON OFF ON ON ON OFF ON ON
OFF ON ON ON ON OFF ON ON
ON ON ON ON ON OFF ON ON
- 27 -
11. TROUBLESHOOTING HINTS
Symptom
Possible cause/remedy
No images on TV
monitor
• Cable is not properly connected to the video-in terminal
of monitor.
• The AC adapter is disconnected from the wall AC outlet.
• The AC adapter output plug is disconnected from the DC
jack of the Camera.
• Zoom is set at TELE to display only white/black part of
the material.
• The LED is lit red, and the Camera is in the OFF
position.
• The LED is lighting, and the OFF Timer mode of the
Camera power is working. (See P.19)
• The cable is not connected to each output terminal.
• The iris is not in the proper position.
(If the iris is fully closed, the image cannot be seen.)
• The chosen video output type (NTSC) is different from
the system of the monitor .
Out of focus
• The focus is in the Manual mode. Set the focus to the
Auto mode by pressing the AUTO button of focus. (See P.16)
• The light/shade contrast of the object is too low. (See P.16)
• The object is moving too fast. (See P.16)
No operation via
• Operation is made with wrong ID number settings. (See P.18)
the wireless remote • Operate within the operation range of the wireless
control
remote control. (See P.7)
• Check the remaining battery life of the wireless remote
control.
• The sunlight or the light from the inverter fluorescent
lamp or the like is received by the infrared sensor on the
Camera. Relocate the Camera or block the light. (See P.7)
• The pin No. 1 of the DIP Switch (4) is ON.
The preset position
is blurry
• The Camera head has been moved directly due to some
cause.
Adjust the Camera direction by setting the "RESET"
button to the normal position. (See P.15)
If the problem still remains after checking the above, consult your nearest dealer or
authorized ELMO service center.
- 28 -
12. SPECIFICATIONS
General
Item
Specifications
Power source
12V DC
MAX.1A
Current consumption
Outside dimensions
Weight /Mass
124mm(W) X 153mm(D) X 136mm(H) (4.9 X 6.0 X 5.4 in.)
mainbody only: 800g (1.8 lb), with plates: 1,100g (2.4 lb)
NTSC compatible
Television system
Output terminal
Control terminal
Power terminal
Composite-video output
RS-485
RCA pinjack/75 ohm unbalanced
Terminal Block
1
1
EIAJ RC-5320A type4
Camera
Item
Lens
Specifications
f = 4.0 - 88.0 (22-times zoom) F1.6-3.8
Zoom
22-times powered (with double speed function) optical zoom
Field of view (Horizontal) 2.3°- 47.5°
Lens filter diameter
Focusing
37mm (1 15/32 in.), pitch = 0.75mm (1/34 in.)
Full-auto/manual
1/4" CCD
Image pick-up element
Effective picture element 768(H) X 494(V)
Total picture element
Minimum illumination
Backlight control
Iris
811(H) X 508(V) (approx. 410,000 pixels)
2 lx
ON/OFF
Auto/manual
White balance
Picture adjustment
Sync. System
Resolution
ATW/push-set/manual
Color balance, AGC gain, Edge enhancement
Internal
More than 460 TV lines (Y signal with horizontal)
More than 350 TV lines (Vertical)
49 dB
S/N ratio
- 29 -
Pan/Tilt
Item
Specifications
Pan range
Left 150° Right 150°
Up 30° Down 90°
Auto/manual (8 speed)
Tilt range
Pan Tilt Speed
Other
Item
Specifications
Title setting
Provided (Camera/preset selection)
Max 223 (PTC-200C) cameras
Daisy chain connection
13. SUPPLIED ACCESSORIES
Item
AC adapter Model NO: D12-10-1000 (5Z0494)
(rated input AC120V 60Hz)
Wireless remote controller (RCW-PTZS)
Batteries (Type R03,AAA)
BNC/RCA adaptor plug.
Fixing plate
Quantity
1
1
1
1
1
4
1
4
4
1
Screw M3x5
Ceiling plate
Wing nut M5
Hexagon head bolt M5x40
Instruction manual
*Weight and dimensions are approximate.
*Design and specification are subject to change without prior notice.
Trademark Acknowledgements
,ELMO are registered trademarks of ELMO CO.,Ltd.
- 30 -
WARNING:
Unauthorized recording of copyrighted, materials, photographs, etc.
may infringe on the rights of copyright owners and be contrary to
copyright laws.
ELMO CO., LTD.
6-14, Meizen-cho, Mizuho-ku,
Nagoya, 467-8567, Japan
OVERSEAS SUBSIDIARY COMPANIES
U.S.A
Elmo Mfg. Corp.
1478 Old Country Road, Plainview, NY 11803-5034
Tel:(516)501-1400
Fax:(516)501-0429
E-mail:[email protected]
Canada
Germany
Elmo Canada Mfg. Corp.
44 West Drive, Brampton, Ontario L6T 3T6
Tel:(905)453-7880
Fax:(905)453-2391
E-mail : [email protected]
Elmo (Europe) G.m.b.H
Neanderstr. 18, 40233 Düsseldorf
Tel:(0211)376051
Fax:(0211)376630
E-mail : [email protected]
Printed in Japan
6X1PTZC02
Receivable range
- 32 -
|